Harvard University Analysis Of The Inductive Circuit Lab Report Hi. Please only bid if you have multism . Hi. Please only bid if you have multism . Name: G

Harvard University Analysis Of The Inductive Circuit Lab Report Hi. Please only bid if you have multism . Hi. Please only bid if you have multism . Name:
GID:
Lab 1:
Grantham University
Date:
Introduction:
Write one to two paragraphs about the Lab. Explain the following information for this lab:
?
?
?
?
What are the goals to achieve in the lab?
What are the expectations of the lab?
How will you be implementing this lab?
What will you try to measure?
Equipment/Components:
List the type of equipment or components that you will be using? Where will you find these
components? How will you use these components in Multisim/VHDL? Explain any adjustments required
such as tolerances.
Procedure:
Briefly describe how you will approach the problem and try to solve the lab, describe and explain any
techniques/rules/laws/principles you would use. Outline each step of the process.
Circuit design:
Take a screenshot of the circuit/logic from Multisim/VHDL as asked in the lab assignment before you run
the circuit and paste it here in your report.
Execution/Results:
Run the circuit in Multisim/VHDL and copy/paste the results from the simulation including any readings,
plots or graphs.
Copy/Paste the screenshots for all the measurements required in the lab here. Be sure to add a title and
explain what each of the screenshots represent.
Analysis:
Analyze the results obtained from Multisim/VHDL and compare those to your calculated results (if
required).
Answer the following questions:
?
?
?
?
What did you discover/confirm?
Use tables and diagrams to record results.
Compare calculations with the measured values.
Analyze your results.
Explain if your simulation is correct or incorrect and why. If the results are confirmed, then your
measurements are correct. If they are not confirmed, explain what the problem is. You will need to
discuss how to troubleshoot the circuit to achieve the correct results.
Conclusion:
Summarize the entire lab in 1 to 2 paragraphs with the results and analysis in mind.
Answer any questions asked in the lab assignment here.
Cite any sources that you may use in your report.
———————————————- End of the page —————————————————————-
——————————————————————————————————————————————
Circuit Analysis – Week #7 Lab
Fourier Series
This week’s lab is based on the application of Fourier analysis of an inductive circuit in Multisim.
You will learn to utilize Multisim to measure the unknown frequencies in the spectrum.
1. Analyze the circuit and determine the output voltage ‘Vout’ of an Op Amp circuit, use a
frequency of 150Hz.
2. Construct Figure 18.15 in Multisim and perform the Fourier analysis.
a. Run simulation to measure the frequency and the voltage gain of the amplifier.
b. Change the input voltage magnitude to the values from the table and run the
Fourier analysis again.
c. Record the frequencies visible in the frequency spectrum in the table.
d. Take the screen capture for the measurements for ‘Vout’.
Measured ‘Vout’
Vin Calculated ‘Vout’ (pk –pk)
Identified frequencies in the spectrum
(pk –pk)
1V
1.5V
2V
3V
3. Answer the following questions:
a. Explain the effect of input voltage on the output voltage of the Op Amp.
b. Express the voltage gain of an amplifier in terms of R1 and R2 and then compute
it.
c. From your measurements, what happens to the output when the magnitude of
input voltage is increased?
d. What is the effect of input voltage on the frequency spectrum? Explain with the
help of measurement results and screenshots.
4. Create a new word document called “Lab7_StudentID.docx” with your GID substituted
into the file name.
5. Save the analysis from step 2 and simulation results from step 3 along with the table and
screen captures of all the measurements. Make sure to answer the questions in step 4.
6. Upload file “Lab7_StudentID”.
Rules for lab submissions:
1. The lab document must be a Word document. PDF files are NOT accepted.
2. All screenshots must be included.
3. All screenshots must include the Multisim time stamp.
4. Any and all Multisim files must be submitted.
5. Any equations used must be typed in Word. Copy and paste of equations from outside
sources is prohibited.
6. No graphics are allowed in the Word document other than screenshots of circuits from
Multisim with the time stamp.
7. The lab template should be used. Specifically, it is brought to your attention that a
summary MUST be provided explaining the results of the labs, the relationship of the
results to expected results, and any challenges encountered.
8. All resistors in must be have a tolerance of at least 5% set. Thus, your measured
values should NOT be exactly equal to your calculated values.
Any violation of the submission rules above will result in a grade of 1.
Lab 7
Grading Rubric
Demonstrate understanding of Fourier analysis
10 points
Analyze the circuit to analyze the output of the Op Amp.
20 points
Circuit design in Multisim
10 points
Measurement of ‘Vout’, Voltage gain and Frequency Spectrum
30points
Answer to the questions
20 points
Lab Report (includes table, measurement with proper units, screenshots, APA
guidelines)
10 points
Total
100
points

Purchase answer to see full
attachment